F.A.Q.

This FAQ Frequent Asked Question
Is intended to explain the technique of components of TIFONE Agriculture Spraying Equipment.
For more technical details, care in the use, causes troubleshooting and repairs also see SERVICE DO IT YOURSELF.
Reset the search

(E±S+) READY = Electrostatic Ready Tifone

Electrostatic Ready feature of machine built and prepared so that it can be completed by Electrostatic Charging Device. Typical of many Tifone Air sprayers.  

AGRICULTURAL PESTICIDE SPRAYING

The activity aimed at protecting the Fruit Trees and Herbaceous Cultures.
The key to success is to achieve the best Possible Coverage with the lowest possible cost.
Some considerations and useful Attention.

Strategic Goals:
  1. Spraying should always reach a sufficient coverage of all surfaces to be protected: Twigs, Leaves and Fruits.
  2. Spray coverage is most effective when it is reached by a sufficient but not excessive wetting, so not to cause the Leaching of the leaves and the consequent "runoff", to ground of spray mixture.
  3. Runoff produces an accumulation of mixture towards the lowest point of the leaves and fruit.
  4. The droplets generated by Leaching and falling to the ground, are high-density, i.e. contain a very higher percentage of pesticide, compare to mixture concentration , as
  5. Very often, the specific weight of the pesticides is greater than the specific weight of water (always in the case of powdered or granular products).

Are therefore obvious other important points:
  1. Lost ground drops for leaching are high content of pesticide dose, then very expensive, and easily reaching up to 50% or more of the mixture sprayed out.
  2. Given that the amount of the remaining mixture on the vegetation is still effective, despite large losses on the ground and to aerial Drift
  3. This means that would have been a sufficient amount of mixture sprayed very minor, i.e. corresponding to the actually remained on the vegetation after the run-off.
  4. It is therefore convenient, first of all, determine the amount of mixture per hectare (litres per Hectare) enough to get total coverage without excessive Run-off and aerial Drift losses.
  5. It is correct, however, emphasise that the disturbances for Run-off and aerial Drift are strongly influenced by other factors, in addition to the operator's attention, namely:
    - the type of plantation (Trellis trees, Crown trees).
    - the density of foliage (depending on the type of plant and the vegetative stage).
    - the type and quality of Air sprayer used.

Maximum uniform and effective coverage in Maximum economy of treatment, you get at the following terms and conditions:
  1. Trellis Trees having:
    - minimum thickness of leaves,
    - easy penetration throughout the thickness of the foliage,
    - a easier top coverage.
  2. On the other hand, Crown trees are much more difficult to penetrate, specially on the top, for the very largest and thicker foliage, where the different overlapping leaves makes difficult to achieve the more internal leaves where spray mist cannot enter easily, with a consequent need of larger spray mixture and a lot more Run-off and aerial Drift loss.
  3. Particularly critical also in Crown trees, to reach a good coverage of Central Cone of canopy, corresponding to the upper part of the same, due to greater leaf thickness, diagonal and greater distance from the outlet of the sprayer.
  4. Pruning of small Trellis in a more "transparent" situation, leaving minimal overlapping branches to create thickness. This condition, as well as to promote a more uniform spray coverage, also encourages greater sun exposure to fruits, with the consequent possibility of lower row spacing with, a larger amount of files/productive plants per hectare.
  5. Using a modern professional Air Sprayer, able to ensure a distribution of spray mist
    - evenly,
    - symmetrically: right = left,
    - spray flow with more powerful from the bottom up, since:
    The lower part of the plant is very close or nearby, and stricken orthogonally, direct,
    The taller part, is always more and more distant and hit increasingly tilted, then according to a longer diagonal and thick vegetation, therefore less penetrable.
  6. It is important to stress that the minimum amount of spray mixture, sufficient to ensure good coverage, depends largely on the quality of distribution of the air sprayer, from its easy adjustability, namely adaptability, to various plantations in the different vegetative conditions.
  7. Among the characteristics of the air sprayer, especially for Trellis trees, and for all the plantations where the central part of row is free from vegetation, Top "V" adjustable deflectors are essential:
    - to avoid useless dispersion in the centre between rows, where no vegetation and
    - to give more power to flows towards the top sides, left and right, the most critical points.
  8. Predetermine the Volume in litres per hectare for the plantation to be sprayed for a minimum amount of spray mixture, enough to guarantee good coverage, with a minimum ground Run-off and a minimal aerial Drift.
  9. Calibration of the atomizer for the plantation. The determination of the Volume of spray mixture, litres/Hectare, permits a correct setting of the Air Sprayer, so as to respect the amount sprayed, with respect of only 2 parameters:
    - distance between rows "between the" (s), in m
    - tractor forward Speed (V), in Km/h,

Utilizing the Formula:

(Litres/hectare (L/Ha) x Row spacing (I) x Km/h tractor (V)) / 600
=
L/min to spray in total R + L 600

For example:

  • the Volume litres/hectare decided is 1000 L/Ha,
  • the Row spacing is 4 m,
  • and the choice for the tractor speed is 6 Km/h.

The formula will be: Example:
(1000 x 4 x 6) / 600
=
40 L/min totally, L+R 600

The formula is telling us that our Sprayer, to ensure a spray delivery of 1000 Litres/ha, in a trees plantation with a row spacing of 4 m and at a tractor speed of 6 Km/h, shall spray out 40 L/min., total L+R. Once decided and activated the nozzle number sufficient for a correct spraying, e.g.: If no. 14 nozzles (7 on each side), are sufficient to cover the entire sides, dividing the 40 litres/min for 14, we find the average flow for nozzle 40 : 14 = 2.85 litres/min. each nozzle.
Be careful: this is the average amount per nozzle but, we know that we must deliver a lesser amount at the bottom of the plant and more and more towards the medium and high part of the tree.
Once you have decided the Volume per hectare to be distributed, and calculated the total value in litres/min, and distributed the litres/min in a growing succession from bottom to top of trees, the best procedure will be:
  1. Prepare the sprayer according to sprayer setting decision,
  2. With spray nozzles for distribution by increasing mixture toward the top,
  3. Proceed with a trial of spraying for 5-10 m,
  4. Then stop,
  5. And make a careful control of the spray coverage obtained,
  6. Inspecting the trees throughout its thickness and its entire height and
  7. Correcting, if necessary, the vertical distribution of the total 40 litres/min (20 per side) in a most appropriate way.

Spray Cover control easy and accurate
Utilizing the appropriate Water sensitive papers strips, similar to post-it notes that, applied to various heights insides of the tree, gather the droplets that, reacting on the sensitive paper, will present very clearly the single spray droplets, the degree of distribution and the intensity of coverage.

This way of control will allow you:
  1. To see the spray result and where eventually improve the sprayer adjustment
  2. The survey of the degree of leaching = ground run off,
  3. The ability to correct appropriately, increasing or decreasing, the Volume of calibration of your Sprayer, i.e. litres/hectare.

Also remember that:
  • The Volume per hectare should be technically and economically, varies considerably according to vegetation state, i.e.:
  • In winter, in the absence of vegetation, Aerial Drift losses will be highest,
  • In summer, in the middle of the vegetation, the Volume required per hectare is higher and Leaching losses will be highest

Therefore, the determination of a correct Volume per hectare, according to trees and growing conditions, and a departure spray control are basic, to get the most effective coverage, with the minimum of spray mixture. And costs.

ANTI WAVE WALL

Panelling arranged transversally within the tank to reduce water hammer, produced especially by rapid braking, and that can produce an uncontrolled violent impact and make it unstable and dangerous driving under certain conditions (available for Vector Big 3000 and Vector Big 4000 and Self-propelled Cobra Interceptor).

ANTI-SLIDING DOWNHILL: SAFETY DISC

For a safe immediate spraying in downhill areas, even after important raining.
Available for all Tifone Tractor Mounted sprayers (Pat. Pend. 2013
Hydraulic ontrolled from the tractor seat.

AUTOFILTER by Tifone

Fully automatic Self-cleaning pressure Filter.
Special system that, unlike usual standard filters, does not retain the foreign bodies, so it cannot get clogged and does not require any cleaning.

 

  • The Autofilter is integrated in the pressure regulator device Telecontrol-Exact. 
  • The Autofilter is equipping all Tifone sprayers.
  • The Autofilter is a completely automatic and self-fluxing filter, so always clean and free. 
  • The Autofilter, unlike normal filters, "does not hold" debris and solids present in the stream, but acts as a barrier between the debris and the spray feeding line. 
  • In the Autofilter, debris are not driven to try to pass through the filter cartridge, but they will remain in the return flow back to the tank. 
  • Return to tank that cannot can't get reliable, as passing through the attempted close by-pass valve of Telecontrol, debris and solids are instantly pulverized by the high pressure and the high speed of return flow in that point. 
  • The Autofilter is much more than a self-cleaning filter as it does not get dirty ever. 
  • The Autofilter is intellectual property of Tifone since 1975.

BRAVO

Line of tractor mounted sprayers by Tifone, 300-400-500 and 600 liters tank,
with high technical specialties such as:

  • General-roundness for a sweet and fluid sliding sideways under the hanging branches and between side vegetation. 
  • Lowered Centre of gravity.
  • Ring-shaped tank Bottom for maximum mixing, preventing sedimentation. 
  • Round tubular frame, recessed and with a bumper function all around.
  • Equipped with suction Probe for a safe dosage of pesticides without any physical contact of the operator and without any risk of dispersion on the ground.
  • Automatic instant mixing of any kind of formulate: Liquid, Powder or Granular.

BRUSH- SPRAY AIR CANNON: Programming Angular System

Angular programming is carried out by means of magnetic poles immediately moved over. The system is simple and totally reliable (solid state).

BRUSH-SPRAY AIR CANNON. Function.

Movement to rhythmic swinging trend, of back and forth of the mouthpiece of the Flexigun Cannon. Useful for repeat function automatically, without the operator intervention. Automatic brush-spray angle can be adjusted instantly, for the required operating angle.

CANNON FLEXIGUN

Type of Cannon for long spray range, with the blast tube powered by flexible sleeve and with a pointing system towards every direction, vertical and horizontal. Ideal for treating Row Crops, vineyards and similar plantations in flat areas, and vineyards and similar plantations in hilly or mountainous areas, where full-directional tracking allows to overcome any spray condition. Also ideal for the spraying in greenhouse crops, where targeting allows better treatment and where, given the environment protected from winds and breezes, they reach very long ranges, with a uniform distribution, favoured by the "saturation" effect produced by the greenhouse environment.

CANNON FLEXIGUN HI-PROFI, E±S READY

Important evolution of Cannon Flexigun classic Tifone, now available in the advanced version, both in terms of higher aerodynamic profile of the blast tube output, both for their predisposition to receive the new high-density Electrostatic Charged with tricuspid high-power polarizing and preventing any short circuits.

CANNON MOUTH = Dual Vide

The cannon mouth is equipped with an additional ventral Outlet.
The Ventral Outlet equipped with ON/Off Facility.
Allows to significantly increasing the spray pattern of the Cannon for spraying large vegetation as hedges, slopes, meadows, etc.
The Dual Wide function is present in Flexigun Cannon 50s and Flexigun Cannon 65s.

CANNON SPRAY HEAD Tifone 45s

See also Super Cannon 45s Dielectric. Electrostatic Ready. New 2013.
Centrifugal blower with a long outlet for maximum air flow guiding, stronger power and maximum spray range

  • Spray Range up to 30 m in open field and up to 40 m in greenhouses.
  • Symmetrical" shaped with same spray height if turned to the right or left.
  • With local soft spraying outlet for seedlings and foliage near the cannon, but
  • With increasing power until it reaches the Jet continuity.
  • The local soft outlet is easy adjustable spray angle.
  • The local soft spraying outlet has automatic repositioning facility right and left, according to spray side adjustment of the cannon.
  • Symmetric shaped Cannon and adjustable Local soft spraying outlet are Tifone property.

CANNON SPRAY HEAD Tifone 65s

See also Super Cannon 65s Dielectric. Electrostatic Ready. New 2013.

  • Large Centrifugal blower with a long outlet for maximum air flow guiding, stronger power and maximum spray range.
  • Spray Range up to 40 m in open field and up to 50 m in greenhouses.
  • Symmetrical" shaped with same spray height if turned to the right or left.
  • with local soft spraying outlet for seedlings and foliage near the cannon, but
  • with increasing power until it reaches the Jet continuity.
  • the local soft spraying outlet is easy adjustable for angle of incidence.
  • the local soft spraying outlet has automatic repositioning facility right and left, according to spray side adjustment of the cannon.
  • Symmetric shaped cannon and adjustable Local soft spraying outlet are Tifone property.

CANNON SPRAY HEADS

Centrifugal blower with a long outlet for maximum air flow guiding, strong power and maximum spray range.
Available at Tifone in 2 versions:

  • Tangential shaped = traditional: Cannon 75, with a spray range up to 38 m in open field or 45 m in a greenhouse.
  • Symmetrical" shaped = with same spray height if turned to the right or left.

CARDAN SHAFT = DRIVE SHAFT…how to get a maximum steering radius

To get the maximum safe steering the following points must be observed:


Adjust or modify the attachment to the tractor and the length of the draw-bar trailed machine, so that the coupling plug pivot is = equidistant between the 2 cruises drive shaft. 
Thus, the total turning angle will be distributed exactly between the 2 cruises.

CARDAN SHAFT Support at rest

Drive shaft support at rest is a very useful device, designed to accommodate and restrain raised end of the drive shaft tractor side, avoiding support for land and protecting it from mud and dust and accidental collisions, during periods of non-use of the machine.
PTO shaft at rest support is available for all models of Tifone ,either tractor mounted and trailed.. (Spare Parts Service, Tel. ...39 (0) 532 730,586, Fax 532-...39 (0) 532-730,588).

CARDAN SHAFT... The correct length

The correct length of the drive shaft must be carried out on the machine that the drive shaft must operate. 
The rule is that:

 

  1. With the tractor aligned with the machine, the two sliding drive shaft tubes must be inserted, one another, again for at least 1/3 of their length. 
  2. Under conditions of maximum steering, the drive shaft must have still a reserve of at least 3 cm stroke free.

CHECK VALVE of the Nozzle

Device to block the spray mixture drip from the nozzle, as soon as feeding is interrupted.

There are several types of check Valves applied to nozzles:

  1. DIAPHRAGM type. It is the most common type. Presents the disadvantage of a large footprint that, with nozzles placed in the current flow of the air sprayer, determines major turbulence and consequent distribution of divergences pest fog, which is particularly negative in the works at reduced distance between rows. In addition, the diaphragm system, determines a certain pressure drop in the circuit, to the detriment of the spraying performance. 
  2. PISTON type. This system does not have any apparent dimension as it simply replaces the feed screw, which is totally. It has the advantage of not producing any drop in pressure in the circuit, because, once opened, the piston is totally outside the flow path.
  3. S/STEEL BALL type Tifone. It has the advantage of an instant closure and extreme simplicity. Also, does not present external body dimensions because the ball system is totally contained in the stem, for which, the nozzles can be placed even in current, without producing additional turbulence.

CIRCUIT FLUSHING SYSTEM

Represents a very important equipment in modern Sprayers. It allows the cleaning function (Flushing) of the entire spray circuit of the machine, from the tank until the nozzles (tank, pump, filters, pipes and nozzles), thereby ensuring a speedy and optimal function for each new use and increased durability of the machine. The Circuit Flushing System is standard in all Tifone Sprayers: Tractor mounted, Trailed and Self-propelled.

COMPACT 36” Spray Tower

New Concept of Spray Tower with following features:

  1. Very powerful.
  2. Able to spray tall large trees as Hops plantations, Nut Trees, Chestnut trees, etc.
  3. Do to it compactness can easily enter any plantation even with hail net.
  4. The slide adjustable nozzles allow specific spray setting.

CONTENT INDICATOR in the TANK

All Tifone Air Sprayers are equipped with content Indicator of mechanical type, index, on a grand scale. Unlike normal hoses, indicators that quickly lose transparency and are very poorly readable, Tifone large mechanical indicators, are unlimited no maintenance need.

 

Mechanical tank content indicator now a standard also in Storm 1500 and in Storm 2000.

CONVEYOR: both side spraying

High power air outlet applicable to Turbofan Tifone to spray row crops, and dwarf trees on both sides, right and left, simultaneously. Equipped with adjustable top deflectors to adjust height of spraying. 

CONVEYOR: single side spraying

High power air outlet applicable to Turbofan Tifone for spraying large tall trees, on single, left side. Equipped with adjustable top deflector to adjust height of spraying and increase power.

COUNTER ROTATING Fans or Blowers

Condition where two  Fans or Blowers are the one turning in the opposite direction of the other.

COUNTER ROTATING “DUAL AXIAL FAN 32+32” SYSTEM AIR SPRAYERS Tifone

Special Air Sprayer concept, offering the following advantages against single Fan.

  • Doubled Spray Power
  • Suitable for the larger tall trees plantations.
  • Able to spray at high speed in Trellis trees plantations. 
  • Totally symmetric uniform spraying: Right side = Left side.  

Available on trailed Vector Line and trailed Storm Line 

COUNTER-ROTATING COMBI SPRAY BLOWERS WITH 2 DOUBLE TURBINES, Tifone

Each double turbine has 2 independent spray Heads:  

- a Fan shaped Orchard Head and a Cannon Head, each independently adjustable. 

Suitable for spraying large trees up to 15-25 m tall.

Have 4 Great advantages:

  1. Exactly Symmetrical distribution, right and left
  2. Double power, compared to a standard air sprayer
  3. Fast and precise angular adjustment of power depending on the width, height, between plants and foliar density of trees.
  4. Minimization of losses to Aerial Drift.

Available on trailed Storm Line and Vector Big line

CRAWLER SPRAYERS Line

Tifone developed an independent Motorized Sprayer mounted on crawler transporter, with the following characteristics:

  1. Full integration, innovative technology brand.
  2. Spray tank in high-density polyethylene and anti-algae treatment, two capacities:
    -  175 liters spray tank, for use in non-planar areas
    -  250 liters, spray tank for flat areas.
  3. Both tanks equipped with mechanical index content indicator and grand scale.
  4. Fuel tank, high-density polyethylene, cap. 30 liters,
  5. Flushing circuit tank in high-density polyethylene, cap. 19 liters.

The CRAWLER SPRAYERS is available in various configurations:

  • Sprayer Crawler with Flexigun Cannon 38, engine 38 hp, spray range up to 35 m. 
  • Sprayer Crawler with Flexigun 15, engine 13 hp, spray range up to 16 m. 
  • Sprayer Crawler with Turbofan 24”, engine 13 hp, spray range up 7 m per side.
  • Sprayer Crawler with Tower 28”/150, engine13 hp, spray range up to 4,5 per side.

The CRAWLER SPRAYERS can be equipped with a front axle with large tires, adjustable track, to accede to very uneven terrain with full controlled stability. 

DIELECTRIC

Insulator, which does not conduct electricity. Typical of the Advanced Technology Tifone Turbofan, made of Dielectric material (mainly HD PE), to allow the application of the Electrostatic Charging, new Tifone system, high density and integral, spread over the entire surface of the spray mixture emission area.

DIRECTIVE 127/CE-2009

The new CE Directive has been in force since 1 June 2012, requiring a precise preparation of pesticide spraying. In summary:

  • Flushing of full spraying circuit of the sprayer after spraying.
  • fast connection to the pump for flow control by flow meter.
  • fast connection to the pump for pressure control manometer.
  • fast connection for a handgun to the outer wash at the end of the day/work.
  • Label with indicated the type of Pesticide in use.
  • 1 liter graduated Container.

DUAL CANNON 45s SPRAYER

Special Double Compact blower equipped with 2 Cannons 45s, Dielectric.

Suitable to spray Horizontally, 25 m per side, for a total of a spray front of 50 m.

Suitable to spray Vertically, up to 25 m to spray tall trees, also with automatic tilting move.

DUAL CANNON 65s SPRAYER

Very Powerful Special Double Compact blower equipped with 2 Cannons 65s, Dielectric.

Suitable to spray Horizontally, 35 m per side, for a total of a spray front of 70 m.

Suitable to spray Vertically, up to 35 m at tall trees, also with automatic tilting move.

EASY VARIO Trailed Sprayers Line

EASY VARIO can be defined an “Extraordinary Evolution of the Species” with many (many)

Inedited advantageous solutions is presenting, amongst them:

  • Front fan: overcharged by the advancing speed = 25% more air volume.
  • Tangential rear oblique spraying: better spray coverage, reduced side drift, far from tractor driver.
  • Easy fast Propeller Regulation: easy power adjust for minimal spray mist Drift.
  • Immediate access and control to Pump and Gearbox.

And many other.

ECO Sprayers, Tractor Mounted Line

New Advanced very compact line. 

Very short in length, grants max stability even to smaller tractors. 

Tank capacity: 200 and 300 litres.

Spray fan: Turbofan 20”, 24” and 28”.

ELECTRO DRIVE, add-on

For Tifone Manual Hose Reels Rollers that, with the simple addition of special electromotor unit enables the transformation from Manual to Electric version 

ELECTRO PRESSURE REGULATOR

Device to adjust the pump pressure remotely through electric control. Consisting of an add on system that is mounted in place of the normal red knob manually operated. 

ELECTRO VALVE

Device for controlling the ON/OFF function of spray nozzles, remotely, by Electric control.

ELECTROSTATIC CHARGE, Type of Polarizer for Cannon

Classic polarizer was, and still is generally, made by a ring in Brass or S/Steel, placed at the end of Cannon mouth. This solution is critic as subject to short circuits procured by the deposit of pesticides that are cumulating between the ring itself and the cannon mouth. Consequence is a loss of Electric Charge, till to produce important local burnings. Even up to the risk of fire.

 

The new innovative Polarizer patented by Tifone has a Punctual tripod shape, where fixing feet are laying very distant from Cannon end and nozzles, are absolutely constantly dry with no risk at all to be wet by the nozzles and so with no risk of any possible short circuit nor lose of energy. 

ELECTROSTATIC CHARGE, Type of Polarizer for Spray Tower by Tifone

Classic polarizer was, and still is generally, made by a ring in Brass or S/Steel, placed around the single nozzle. This solution is critic as not allowing of moving nor orienting the single nozzles.


The new innovative Polarizer patented by Tifone is an integral polarizer running around the whole periphery of Tower spray wall, independent from the nozzles and assuring an integral polarization of the full spray discharge area. No risk of short circuit.

ELECTROSTATIC CHARGE, Type of Polarizer for Turbofan

Classic polarizer was, and still is generally, made by a ring in Brass or S/Steel, placed around the single nozzle. This solution is critic as not allowing to move nor orient the single nozzles.


The new innovative Polarizer patented by Tifone is an integral polarizer running around the spray wall, independent from the nozzles and assuring an integral polarization of the full discharge area of the Turbofan. No risk of short circuit.

ELECTROSTATIC CHARGE… Spraying assisted by Tifone

A New Technique With Real And Visible Results. The theme of the Pesticide spraying, is assuming increasing importance, due to the growing need to achieve more and more advanced, Objectives, including:

  1. Effectiveness of interventions, 
  2. Reduction of the number of interventions, 
  3. Reduction of losses due to aerial Drift, 
  4. Reduction of losses for Results on the ground, 
  5. Reduction of chemical Charge per hectare, 
  6. Reduction of Energy Consumption (fuel), 
  7. Reduction of spray time.

These goals, all of high interest and of increasing weight and attention, both for the environment and food safety and, last but not least, for the a better Farm economy.
So, in order to optimize the spraying as desirable, utilizing new technologies and new aerodynamic attention has come to develop innovative solutions significantly more effective, compared to the state of the art.


Today, spraying assisted by Electrostatic Charge (E±S+) of new generation by
is giving relevant and visible results.
It is known that the electrostatic charge system, in pesticide spraying in agriculture is based on the fact of applying a Positive electrostatic charge (+) to the spray droplets, launched by the Air sprayer.
The optimal use of Electrostatic Charge, however, also requires the optimization of conditions of release and Camera capabilities, electrostatic, and permeation of mist flow electro-loaded, from launch.


The new Electrostatic Charging (E±S+) system by Tifone, is based on the development of the Area subjected to electrostatic charging (Ionization) and efficacy of ionizing emission and efficiency of the "Polarizer" implemented. The advanced system of new generation uses and "tune" the following conditions.

 

  • C1.. Anti-drift, 
  • C2.. Protection Windbreak, 
  • C3.. Permeation ionization (E± S+), intense field, 
  • C4.. Flow Guide "long-range". The Spraying assisted by Electrostatic Charging (E± S+) is more complete, even in parts less directly exposed to Cannon mist Jet.


In addition, the system of Electrostatic Charging (E± S+) significantly reduces Aerial Drift and Ground Dripping. The phenomenon can be perceived clearly even through simple Visual observation. With the system Electrostatic Charging (E± S+) spraying is also possible at Low Volumes and Ultra Low Volume (ULV), which allows the drastic reduction in the volume of spray mist needed, with savings of formulates even up to 50%.


The economic saving, is the direct result of recovery "due to electrostatic charge" of disturbances, to reduce excess wetting, to reduce the air and drift reduction of dripping on the ground. As you can see, with the treatments assisted by the new Tifone ELECTROSTATIC CHARGING (E±S+), all target points, listed above are reached or approached considerably.
The new Tifone system to Electrostatic Charging (E±S+) is available for several types of Ventilators – Sprayers:

  • Flexigun Cannons (Dielectric)
  • New Cannon 45s, symmetrical (Dielectric)
  • New Cannon 65s, symmetrical (Dielectric)
  • New Turbofan Front suction 32AA (Dielectric)
  • New Front suction Tower 32/180- AA (Dielectric) 
  • New Front suction Tower 36/210- AA (Dielectric)
  • Easy Vario 1000 (Dielectric)
  • New HLV System (Dielectric)
  • New Dual “T” Cannon (Dielectric)

FAN or BLOWER CAPACITY

Is the amount of air produced by the fan / blower. Expressed in cubic meters per hour (cm/h).

FILTER MESH

Identifies the mesh density filters. Can be expressed in mm as width of the mesh holes.

The mesh size of Tyler is the number of openings per linear inch of mesh. For example, a 4 second Tyler is a shirt that has exactly 4 openings per inch and 16 per square inch. (= N. of holes on a square of side length 25.4 mm). This type of measurement is used to define the various filters of a modern Air Sprayer: Input filter in the tank, suction filter upstream of the pump, pressure filter downstream of the pump.

FIXED NUMBER

Fixed value generally assumed in a calculation formula. Equivalent of "constant".

Often represented by the letter "K". 

FLOW DEFLECTORS TOP-TOP

Manual o Remote Controlled.


The Spray Tower 32/180 AA Dielectric and the Spray Tower 36/210 AA Dielectric by TIFONE are equipped with Flow Deflectors Top-Top "Great-Guide", for the control of Spray Mist Drift in the middle of the rows. The Top-Top Flow Deflectors are Manually or Instantly Remote controlled from the tractor seat, for a prompt precise adjustment in maximum comfort.

FLOW METER

The flow meter is a device allowing instant measurement and spray flow control provided by the sprayer. Measurable streams from Digital FLOW METER are:

  1. instant spray flow supplied at the spray RIGHT side. 
  2. instant spray flow supplied at the LEFT side. 
  3. instant flow RIGHT + LEFT 
  4. TOTAL ... Temporal Scope, Delivered during a certain period of time. 
  5. Scope for treatment provided in a certain plot. 
  6. Total Capacity delivered at certain date or time. 

The Digital FLOWMETER consists of 2 main elements:

 

  • flow detector Group and 
  • computer - Digital Screen.

 

To ensure a smooth functioning over the time it is essential the flow meter is flushed (cleaned inside) with clean water after each use of the machine. In case of non-functioning, almost certainly this is due to lack of flushing, and consequent sedimentation of chemical. 

To restore operation, you need to disassemble it sand remove any residue.

FLUSHING: valve with 3-way

For the selection of 3 functions: SPRAY (spraying), FILTER (suction filter cleaning), FLUSH (flushing). 

GALVANIZING: by electro zinc coating

Anti-rust treatment obtained by immersion of the piece to be protected in a galvanic bath (electrolysis).

GALVANIZING: by hot dip

Very effectively rustproof and durable obtained by immersion of the piece to be protected in a bath of molten zinc. System widely used throughout the production Tifone. 

GEARBOX

The organ that multiplies the speed of the tractor's PTO (540 RPM) leading to the speed set for the fan Propeller or Turbine. Gearboxes used in Tifone air sprayers are all of type and design and exclusive study and realization and guarantee top mechanical and aerodynamic performance, and a virtually unlimited duration. For good maintenance see SERVICE: Do It Yourself. 

H.L.V. Sprayer (High Low Volume)

A innovated concept of this sprayer with the introduction of facilities giving wide possibility of adjustment and regulation assuring an inedited adaptability to various plantations and virtually to any kind and level of spray need:

  • 100 % uniform spray pattern.
  • 100 % spray symmetry, Right and Left.
  • spray pattern Angle adjustment by 4 independent Air vanes: Left side, Top left, Top right, Right side.
  • spray pattern Power adjustment at side and top, by 4 independent Knob adjusters: Left side, Top left, Top right,  Right side.

Realized totally in HQ Dielectric material.

Ready to receive Tifone Electrostatic Charge, High power (E±S+)

HAND-WASHING TANK + CONTAINER for PESTICIDES

Safety Rules prescribe that any sprayer has independent tank containing clean water for washing hands and rescue washing face, in case of accidental contact with pesticides.

Safety Rules also prescribe that pesticide must be kept in a safe condition against improper use.

Tifone achieved combined containers, with two separate ponds, areas of Clean Water and Pesticide packaging container, which can then be provided in the same machine, with the advantage of the autonomy of the doses, for charging water tank at different points during the day. The Pesticide container is equipped with a safety lock to prevent abusive or risky picks by unauthorized persons.

HOSE REEL with 4 hose-guide rollers

Device for collection of rubber tube, to power the handgun or Pistol Nozzle for manual spraying. The Tifone Hose Reels enjoy supervised technical implementation and advanced, with exclusive advantages: 4 needle roller guide system-tube, Integrated locking lever, Bearings lubricated for life, Structural strength, Tropical Galvanization, Manual or Electric drive.

HOSES with safe mounted hydraulic fittings

New professional Tifone system ensuring maximum reliability over the years.

INCH

Anglo-Saxon unit, corresponding to 2.54 cm. Still widely used in Italy to establish fitting measurements and the diameter of the propeller or fan, or else. 

INJECTOR

A static typ pump, based on 'Venturi tube principle’. Used as a spray mixture mixer or as a tank filler, taking water from a deposit. Also called "Ejector".

INSTANT POWER-ADJUSTABLE PROPELLER

The Tifone propeller adjustment is quick and easy. And is obtained so practically instant, in just 6 seconds on the field.

 

Unlike Normal Propellers, declared as "variable pitch" where you must remove all  single blades, one by one, and replace them according to the desired angle. Practically not possible operation on the field because it requires tools and workshop and that takes approximately 30 to 40 minutes.

INSTANT POWER-ADJUSTABLE Tifone PROPELLER

Propeller adjustment allows to decrease or increase, instantly, the Volume of air produced by the spray fan, then the real power of spraying effect, with the following advantages:

  1. Size the power and fit exactly to any kind of tree or herbaceous Crop,   
  2. Avoid excess spraying, technically and economically negative,
  3. Minimize losses to Drip to the ground and,
  4. Minimize large losses to aerial Drift,
  5. Allow operating the air-sprayer with very low power tractors,
  6. Allow considerable savings in fuel and tractor,
  7. Considerable noise reduction and less environmental pollution.

MANOMETER or PRESSURE GAUGE

Device indicating pressure (bar) at which the circuit is regulated.

The Tifone gauges feature:

  • reading scale with 0.5 bar fractioning.
  • reading scale with different functional pressure value areas. 

MIN.

Abbreviation for minute, the 60th part of an hour.

MIXING OF SPRAY MIXTURE

System to keep mixture well mixed in the tank and to ensure a uniform chemical concentration. Particularly effective and advanced mixing systems by Tifone.

MIXING: Double and Multiple

Advanced system that allows you to achieve and maintain uniformity and consistency of spray mixture concentration within the tank. This system in many models Tifone.

NOZZLE HOLDER

Often mistakenly referred to as nozzles. In fact, the nozzle holder is the device that hosts the spray mist nozzle inserted in the Nozzle holder. Nozzle holder usually includes a stem or stalk, a head to 1.2, 3 or more seats, and a non drip Valve (check valve). The Tifone studies and realizes its own nozzle holders for some advantageous technical exclusive features:

  • Unified Ring: designed to accept all types of nozzles (ATR, Disc, Plate, Anti-drift, etc.) 
  • Very compact Head, smaller footprint. 
  • Head allowing a tangential inclination, for mounting of Nozzle holders outside the air outlet, to avoid vortices generated if placed inside the air outlet. 
  • S/steel Ball check valve, totally integrated, without any bulky prominence.

NOZZLES

Spray tips placed on the nozzle holder, aimed at transforming the spray mixture in the form of mist Media, Fine or Thin, depending on the type of nozzle and the pressure of the feeding circuit. 

PESTICIDE CONTAINER + THROAT hose reel (20 m)

Special accessory to the new Tower 32/180-AA PE Dielectric and new Tower 36/210-AA PE Dielectric as safe container for Pesticides with external round throat as hose reel up to 20 m hose and Lance Mitra to spray finish points where the machine cannot go. The container for packaging pesticides equipped with a screw cap and a safety lock, to prevent abusive or risky picks by non-authorized people. Another idea by Tifone.

PESTICIDE SAFETY CONTAINER + FRESH WATER CONTAINER

Useful combination made and integrated in the new Sprayers VECTOR Big 3000 and VECTOR Big 4000 liters.  The container for packaging pesticides equipped with screw cap and safety lock, as prescribed by law, to prevent abusive or risky picks by non-authorized people.

Plus fresh water tank for hand wash,12 liters.  Another original idea by Tifone.

POLARIZATION

Process followed by a electrical polarity in a body. Typical the case of Electrostatic Charge where the mist droplets emitted by an air sprayer, are loaded with electro-positively, to promote the attraction of each item connected to the land, particularly the vegetative part of the plant, in Viticulture, Arboriculture and Row Crops. 

POLARIZER: tripod Spire

The original Evolved Polarizing system, devised by Tifone for the Mist spraying cannons, with the advantage that, given the presence of anchor very backward feet than mouth Cannon, spray prevents any risk of short circuits from sedimentation of pesticide products, typical problem of usual Annular Polarizer.

POLARIZER: Annular

Device of specific form to transmit an electric polarization. 

POLARIZER: Continuous Linear Profile

innovative Form. Has the advantage of producing and keeping the polarization Charge on the entire spray mist outlet of the sprayer, and not only on single nozzle, with the advantage of great simplicity and maximum constant charge power, even in the case of variable nozzle position.

POLYETHYLENE

Macromolecular Compound obtained by the polymerization of Ethylene. Polyethylene is today considered the ideal material for the construction of smooth inside tanks and various products pesticide-resistant and shockproof. Tifone was the first manufacturer to produce Polyethylene tanks for its trailed mist blowers in 1989 and is still the only one in the world to have complete lines Trailed models with capacity from 600.800.1000.1500. 2000.3000 and 4000 litres (STORM, VECTOR and VECTOR Big Lines)

PRESSURE: Adjusting knob

Typical the one of the pressure regulator Telecontrol ''Exact'' by Tifone.

PRESSURE: Constant

Important Feature required for CONSTANT pressure regulators, in order to ensure good adjustment of spraying, then the Volume per hectare.

Found only in quality, high sensibility pressure regulators. Exceptional the Telecontrol Autofilter Exact bys Tifone.

PRESSURE: Regulator

Device for adjusting the pressure in the circuit of the sprayer. Typical and exceptional the Telecontrol Autofilter 'Exact' Tifone which presents total stability and constant pressure.

PROPELLER: FAST ADJUSTING

Adjusting of a TIFONE Propeller is fast and easy.
You should, however, do a little practical exercise, to learn how to run the operation with ease and in just 6 seconds.

Some Basic Information:
As the Propeller has a limited inertial weight, is that the operation of the locking release, shall be made with a fast movement.
You only need to learn how to make the required quick movements with the "adjusting key".
The safety grid of the fan has a central disc with a hole, for the entry of adjusting key, and to reach the centre of the "Big red nut" with a cross-shaped indentation.
Through one of the several slots of the same grid, the adjusting key can then reach a "peripheral slots" found on the propeller cup, cup whose rotation determines the instant adjustment of the 8 propeller blades altogether.
The adjusting key will be rotated "counter clockwise" to loosen the "Big red nut” propeller, and clockwise to relock it, after the blades adjustment is done.

How to proceed:

  1. Hold the adjusting key as follows (for "right-handed" operators):
    • With the Left hand, hold the straight end of the adjusting key (the long end with the final bent as "L")
    • With the Right hand, firmly hold instead the articulated extreme short end of adjusting key.
  2. Now focus on the fact that your left hand will only keep the bent end within the cross notch of the "Big red nut", while, with your right hand, you will have to transmit an "instantaneous momentum," strong enough to loosen the "Big red nut".
  3. Focusing now on the light weight of the propeller itself, we must use the most of its low inertial mass.
  4. So, if we apply a slow torsional movement, we do not get enough impact to unlock the "Big red nut". A quick right hand movement, a "jerk", is essential.
  5. Prior to the rapid movement thereof, to get a higher torsional effect, you must also take a short pre-rotation of the propeller in the opposite direction, and then make the move as quickly as possible, in the direction required for the function (Left hand to release, right hand to relock)
  6. Repeat a few times to become familiar with this type of fast motion, focusing on points 2.3.4.5., and the operation will soon become easy, instinctive and effective.
  7. Be careful not to overdo the locking of "Big red nut".
    In fact, the force required to release it is a bit 'higher” than the force required for locking, once the adjustment is made. If you block the "Big red nut" too strong, it will be necessary a greater force to unlock it, next time you have to change the adjustment.
  8. So, No need, to over tighten the "Big red nut".
  9. Normally, it is sufficient a tightening average, obtained with 2-3 pulses, to prevent any accidental
  10. loss of adjustment.

PUMP

The pump is the device that allows you to take the spray mixture from the tank of the machine and send it to the nozzles, at a regulated pressure. The pump also serves to supply some additional functions of the sprayer such as : Mixture mixer, Suction and instant mixing  of spray chemicals - Liquid, Powder or Granular-  spray handgun, fill the tank, cleaner etc.

The pumps equipping Tifone air sprayers enjoy exclusive features and advanced technology, including:

  • bronze-connecting Rods
  • direct Outlets
  • delivery meeting the stated Capacity
  • compactness
  • fluid silent Operation
  • constant Pressure. 

PUMP CAPACITY

Is the amount of fluid that can be supplied by the pump, expressed in liters per minute. 

PUMP DIAPHRAGMS

Pump pressure elements that separate the mechanical part of the pump from the pump circuit. Generally in Nitril rubber. In case of use of particularly aggressive pesticide Formulations are preferably used in special compounds such as VITON ®, DESMOPAN, etc. 

PUMP DISCHARGE VALVE

Allows quick and total emptying of the pump, without removing the suction-delivery valves. Useful for quick emptying of the pump before the winter break and for quick emptying of the pump in areas with risk of frost. A standard in Tifone sprayers.

PUMP: Pressure

It is the value in bar at which you are using the sprayer.   

QUALITY

Conditions of functionality, operability, reliability, durability, safety and aesthetic pleasantness requests so and ever-higher level of business and law, for all products and services. The concept of quality tends to include the price level, which should not exceed the limits of market. 

RESET (-point)

Present in the anti shock system of Tifone Flexigun cannon. Corresponding to the point at which it must normally be adjusted the base of Cannon Mouthpiece, to obtain an angle of the cannon pointing within the normal operating range. Important: a setting different from the one corresponding to the point of "Reset" allows you to aim the cannon on any different spray sector. 

ROLLER ANTI-M, with DISCS ANTI-SLIDING DOWNHILL

For a safe spraying in downhill areas even after imprtant raining

Available for all Tifone trailed sprayers (Pat. Pend. 2013)

ROLLER, ANTI-MUD.

Allows to spray immediately, , without any delay,  even after intensive raining, preventing from sinking into the mud and reducing the existing carriageways.  

The depth, the height of the roller is controlled hydraulically from the tracto.r.

Available for all Tifone trailed sprayers (Pat. Pend. 2013)

ROUGHNESS

Important Characteristic in tanks for sprayers. By law, the roughness of the internal and external walls of tanks for sprayers must not exceed 0.1 mm. Fiberglass tanks are smooth on the outside but inside is very rough, so have long been outlawed.

All Tifone tanks are made of HD Polyethylene, perfectly smooth also inside.

Sec.

Short for 'second', the sixtieth part of a minute, the 1/3600 part of an hour. 

SELF-PROPELLED COBRA INTERCEPTOR

A Sprayer with unique features and exceptional. Enjoying over 30 Points Plus that differentiate and classify the absolute top in the field, above any Italian and worldwide competition.

SIDE CLOSING WALL for SPRAY TOWERS for Zero Drift in sensible areas

Side Closing Wall can be on the Right Side, on the Left Side or on both sides.

SPRAY FAN WITH 2 COUNTER-ROTATING PROPELLERS Tifone

Offer the following advantages:

  • double spray power
  • for trees plantation of large vegetative growth,
  • or double-speed spraying Trellis trees plantations
  • however absolutely symmetrical spraying right = left. 

SPRAY HEADS: Tilting

Tifone system applied to ORCHARD Spray Heads: type normal section and  Super Flow Heads, greater power, tapered section. The system produces a swing movement of the Spray Head assembly favoring the movement of leaves with a maximum of penetration through the foliage.

The Tilting Heads system is particularly suited to plantations with higher leaf density, including  orange groves, other citrus fruits, etc.

SPRAY PATTERN CONTROL: Horizontal

Site equipped for the relief of the range and distribution of spray mist lanced by spray Cannons. Essential equipment for studying, testing, fine-tuning and optimization of spray "coverage"

Present at Tifone with a useful relief range up to 50 m.

SPRAY PATTERN CONTROL: Vertical

Vertical wall for the relief and the calibration of the distribution of the mist emitted by sprayers for orchards and vineyards. Is the ideal and indispensable equipment for studying, testing, tuning and optimization of professional sprayers. Present at Tifone since 1972.

SPRAY TESTING SITE FOR CANNON: by Tifone

Spray Testing range up to 50 m 

Cannon sprayer performance is evaluated under some parameters:

  1. Maximal spray range with standing sprayer (for in Greenhouse spraying)
  2. Maximal spray range with sprayer moving at 3 km/h (for open field spraying)
  3. Quality of spraying at different distances from the cannon outlet to the end of useful spray range
  4. Possibility to turn Cannon to spray Right hand or Left hand (also to take advantage of breeze    and wind condition)

Spray TOWER

Spray Fan Apparatus, axial propeller, generally, with a vertical shape. Offers the advantage of deploying more regularly distributed to various heights. Tifone has developed and is producing several types of particularly advanced towers, including the original "tapered" form that allows perfect adaptation particularly to rows without the risk of touching and damage vegetation and fruits even in case of strong vertical inclination given to strong inequalities of the ground.

Spray TOWER, 32/AA-180, Tapered, Dielectric and (E±S+) Ready

With a 32" fan, adjustable air volume up to 45.000 mc/h for calibrated and dosed professional spraying of Palmette (Trellis trees) with a row spacing up to 5 m and a height up to 5 m.

 

Special achievement totally in noble dielectric material HD-PE. Characterized by a totally Symmetrical Distribution in 4 quadrants. 

 

Equipped with Adjustable Propeller for instantly air Volume power adjustment to the type of plant and the density of the vegetation at the time, minimized aerial drift and Dripping on the ground.

 

Due to the achievement in noble, Dielectric material it is designed for the application of intensive Electrostatic charging (E±S+), full polarization, powerful and active along the entire spray discharge outlet, right and left, with a further reduction of the general loss and drift.

 

Perfectly tapered form allows access to high-density systems without ever touching the foliage or fruit.

 

Can be equipped with remote controlled Side Closing Wall for Zero Drift in sensible sites.

 

Side Closing Wall can be on the Right Side, on the Left Side or on both sides. 

Spray TOWER-36/AA-210, Tapered, Dielectric and (E±S+) Ready

With 36" fan, adjustable air volume up to 68.000 mc/h for calibrated and dosed professional spraying of Palmette (Trellis trees) with a row spacing up to 6,5 m and a height up to 6,5 m.

Special achievement totally in noble dielectric material HD-PE. Characterized by a totally Symmetrical Distribution in 4 quadrants. 

Equipped with Adjustable Propeller for instantly air Volume power adjustment to the type of plant and the density of the vegetation at the time, minimized aerial drift and Dripping on the ground.

Due to the achievement in noble, Dielectric material is designed for the application of intensive Electrostatic charging (E±S+), full polarization, powerful and active along the entire spray discharge outlet, right and left, with a further reduction of the general loss and drift.

Perfectly tapered form allows access to high-density systems without ever touching the foliage or fruit.

Can be equipped with remote controlled Side Closing Wall for Zero Drift in sensible sites.

Side Closing Wall can be on the Right Side, on the Left Side or on both sides. 

STEP BETWEEN PLANTS

Distance between two successive plants on the same row of plantation. 

STORM Sprayers Line

Mist blower Tifone trailed, 600, 800, 1000, 1500, 2000, 3000 and 4000 liters. Characterized by typical of STORM points: The indestructible. In over 25 years of production have never broken even a tank, even in the event of rollover.

  • Tanks in top quality Polyethylene
  • side filling port
  • all commands on the left side
  • Sucking-instant mixing Probe Draws all kinds: liquid, powder and granular.
  • Double frame, unparalleled strength
  • Axles are adjustable in height and width
  • Drawbar is height and length-adjustable
  • Short steering drawbars, field and road approved.

SUCTION PROBE for pesticides

Special Tifone device sucking directly from the original packaging (bottle, bag, box).  Fast and safe: sucking any kind of pesticide, Liquid, Powder or Granular, that is dissolved-mixed instantly and automatically downloaded within the filter of tank filling hole.

 

And not directly into the tank, where it would sediment without dissolving-mixing ever completely! 

 

In addition, With the Suction Probe:

  1. no dispersion of Pesticides in the environment.
  2. the Operator does not touch or inhale pesticides anymore.
  3. the Operator does not dissolve more powder and granulates in a bucket or other container.
  4. the Operator  No bucket, means no risk, when to be poured in high tanks.
  5. the Operator is certain of the total mixing (total!) of Powders and Granulates.    
  6. the Operator saves time.
  7. the Operator works in total safety and hygiene.

SUPER CANNON 45s. Dielectric. Electrostatic Ready. New 2013

Useful spray Range up to 30 m in open field and up to 40 m in greenhouses. Centrifugal blower with long guided axial outlet for maximum power and maximum spray range.

  • symmetrical outlet axis, issuing the same height when turned to the right or left:
  • "Soft Close" additional outlet for the soft spraying of seedlings and foliage near the cannon, but with increasing power until it reaches the continuity of spray distribution.
  • "Soft Close Spraying" additional outlet for fully adjustable angle of incidence.
  • "Soft Close Spraying" additional outlet for automatic repositioning, right and left.
  • "Soft Close Spraying" additional outlet is a Tifone idea.

SUPER CANNON 65s. Dielectric. Electrostatic Ready. New 2013

Useful spray Range up to 40 m in open field and up to 50 m in greenhouses. Centrifugal blower with long guided axial outlet for maximum power and maximum spray range.

  • symmetrical outlet axis, issuing the same height when turned to the right or left:
  • "Soft Close" additional outlet for the soft spraying of seedlings and foliage near the cannon, but with increasing power until it reaches the continuity of spray distribution.
  • "Soft Close Spraying" additional outlet for fully adjustable angle of incidence.
  • "Soft Close Spraying" additional outlet for automatic repositioning, right and left.
  • "Soft Close Spraying" additional outlet is a Tifone idea.

TANK: residue

The remaining quantity that remains in the tank, as not pumped from the spray circuit, or non-downloadable through the tank drain valve. Particularly minimal in all Tifone machines, given the high inclination and shape of the tank walls and bottom. 

TANK: total emptying

Important characteristic to ensure full utilization of the contents of the tank even when working on steep slopes.

TANK: total utilization of the contents

Total emptying of the tank with 'Zero' residue. Advanced quality feature to ensure the full use of the contents of the spray tank, so as to also avoid subsequent stratification of solid residues.

The technical residue in Tifone spray tank is very minimal.

TANK: with bottom deep apex

Designed for total utilization of its content in condition of slope, even pronounced

TELECONTROL AUTOFILTER EXACT

Special pressure regulator Tifone with exclusive features:

  1. automatic self-cleaning filter 'Autofilter', integrated,
  2. constant Pressure
  3. micrometric adjustment of the pressure
  4. Gauge with read scale every 0.5 bar. 

TUNNEL SPRAYER, “Zero Drift”

Special sprayer equipped with secluding walls preventing any aerial Drift loss and with a recovery system allowing to recycle all spray mist in excess.

Offers the great advantage of doing contemporary active spraying on both sides of the tree with a maximum penetration and effectiveness, with almost cancellation of Run-off and a real ZERO aerial Drift.

Allows saving of at least 50% of spray mist, 50% fuel and 50% spraying time, compared to traditional air sprayers.

Significant and particularly advanced and innovative the "TUNNEL-T2", Bilateral Tunnel by Tifone, for the advanced innovative lay-out of nozzle ramps, assisting air flows, air barrier and additional exclusive benefits:

  1. Tangential spray nozzles and air flows for a deep spray penetration till over centre of also large leaves vegetation
  2. Large powerful blower operated mechanically : no hydraulic, no electric power required
  3. Steering electronically coordinated to tractor steering.
  4. Compact and lightweight.
  5. Simple advanced design and conception.
  6. Conceived to last decades.
  7. Simple and safe maintenance with integrated climb steps and workspace.
  8. Dosage station integrated, with space for sacks, digital weighing balance and instant transfer probe.

A Tifone Pat.Pend.2013

TURBOFAN AA Dielectric (E±S+) Ready

Classic name of Axial Flow Spray Fans by Tifone

Turbofans are available in different diameters 24”. 28”. 32”. 36”. 42”

The Tifone Easy Fast Adjustable Axial Propeller equips all Turbofan.

TURBOFAN-AA, Dielectric, front side sucking

Are equipped with Electrostatic Charge System.

TURBOFAN-AA, front side sucking

This is an important evolution, with positive advantages, against TURBOFAN-AS, rear side sucking:

  • Not sucking any leave nor powder from ground
  • Any recirculation of spray mist. 

USEFUL FORMULAS

  1. Calculation of litres/min. for which adjust the sprayer to produce a given Volume/HA.
  2. Calculation of Litres per hectare corresponding to a data flow in litres/min.
  3. Verification of the speed of the tractor according to the latter used to cover 100 m.
  4. Calculation of the number of plants present in a hectare.

VECTOR Big Line Catalogue

Line of Big Tifone Mist-blower trailed, 3000 and 4000 liters.

Characterized by typical points:

  • tank high quality polyethylene
  • tank well tapered
  • left side filling port 
  • content Indicator by mechanical index on large scale,
  • suction Probe for any kind of pesticide: Liquid, Granular and Powder
  • all commands on the left side
  • double frame, with side belt
  • hemispherical Bow
  • total Sliding keel against mud even after heavy rains and in the presence of deep ruts
  • axle adjustable in height and width
  • drawbar adjustable in height and length
  • steering drawbar of various type, for field and public road. 

VECTOR Line

Line of Tifone Trailed Sprayers, tank cap. 1000, 1500 and 2000 liters. Characterized by typical  points:

  • tank tapered tank totally
  • best quality polyethylene
  • left side filling port 
  • content Indicator by mechanical index on large scale,
  • suction Probe for any kind of pesticide: Liquid, Granular and Powder
  • all commands on the left side
  • frame with hemispheric Bow
  • total Sliding keel against mud even after heavy rains and in the presence of deep ruts.
  • semi axles, adjustable in height and width
  • drawbar adjustable in height and length
  • steering drawbar of various type, for field and public road.

VOLUME PER HECTARE

The Volume-Hectare, is the amount of spray mixture distributed per hectare, and varied depending on the trees and plantations (trees height, leaf density, vegetative growth, kind of parasite to control, tractor speed ...). It is therefore necessary to be able to quickly calculate the litres/minute match, in order to calibrate the atomizer for the Volume per hectare. The value of l/min at a given Volume per hectare, is obtained through the known formula:

litres/Hectare x Row spacing m x Speed Km/h tractor
________________________________________________ = litres/minute.
                                   600

To other formulas, see USEFUL FORMULAS.

ZERO RESIDUE

Catch phrase, referring to a tank that is emptied completely and ensuring full use of its content. 

top
Work in progress
stay tuned